Linear RE-1 Manuel d'utilisateur

RE-1Residential Telephone Entry SystemWith Built-in Wireless Receiver(760) 438-7000USA & Canada (800) 421-1587 & (800) 392-0123Toll Free FAX (

8CONTROL WIRINGGate Control1. Route two wires between the gate and the RE-1. Connect the gate operator’s OPEN terminals to the RE-1 Relay #1 COM &

9POWER, BATTERY, & GROUND WIRINGPower Wiring✦ NOTE: DO NOT APPLY POWER UNTIL THE INSTALLATION IS COMPLETE.1. Route two wires between the RE-1 and

10OPTIONAL KEYSWITCHA keyswitch can be installed in the RE-1 Entry System to provide keyed access. The RE-1 case is designed to accept the following

11OPTIONAL CCTV CAMERALinear’s Model RE-BWC1 (P/N ACP00886A) CCTV camera can be installed inside the RE-1 Entry System. The camera provides a video si

12PROGRAMMING ACCESSThe RE-1 can be programmed locally or remotely. The system’s built-in programming software can be accessed on-site or off-site usi

131. FROM CONTROL PANEL SELECT "NETWORKCONNECTIONS" THEN SELECT "NEW CONNECTIONWIZARD"2. THE NEW CONNECTION WIZARD WILL STARTCLICK

142. CLICK "DIAL"TO START THECONNECTION6. AFTER CONNECTING, SWITCH TO YOUR MICROSOFTINTERNET EXPLORER BROWSER SOFTWARE ANDENTER THIS ADDRESS

151. FROM THE START MENU, CLICK ON "CONNECT TO"SETTING UP A WINDOWS VISTA™ DIAL-UP NETWORK CONNECTION (PART 1)2. CLICK ON "SETUP A CONN

167. CLICK ON "CLOSE"SETTING UP A WINDOWS VISTA™ DIAL-UP NETWORK CONNECTION (PART 2)8. FROM THE START MENU, CLICK ON "CONNECT TO"

171. CLICK ON "DIAL" START THE CONNECTIONCONNECTING TO THE RE-1 WITH WINDOWS VISTA™2. THE MODEM WILLDIAL THE NUMBER3. ONLY WHEN CONNECTING R

CONTENTS FEATURES• TWO-WAY SPEAKERPHONE• CALL WAITING• CALL FORWARDING• DISTINCTIVE RINGS FOR ACCESS CALLS• SEVEN ACCESS TIME ZONES• TIMED “DO NOT DI

18LOCAL PROGRAMMING ACCESSProgramming with a Local Telephone or the Unit’s KeypadStart with Step 1 below for local programming with the unit’s keypad

19PROGRAMMING REFERENCEPROGRAMMING CONTROLUSAGE KEYSTROKESENTER PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20BASIC SYSTEM PROGRAMMINGEntering Programming ModeThe 6-digit Master Programming Code (default = 123456) is used to enter Programming Mode from a loc

21TRANSMITTER PROGRAMMINGAdding TransmittersUp to 24 groups of transmitters can be assigned common access privileges sharing the same one or two time

22Call Forwarding Feature Default: OFFThe call forwarding feature will allow a visitor to contact the resident at the programmed telephone number ins

23Relay #2 Alternate Options Default: Access RelayRelay #2 can be used for functions other than triggering a gate operator or door strike. Relay #2 c

24Keypad Beeps On/Off Default: OnThe default setting causes the main keypad to beep when each key is pressed. The beeps can be disabled.Press: Ke

25RE-1 OPERATIONRequesting Access with an Entry Code• Visitors have up to 40 seconds to key in their entry code.• Up to eight seconds are allowed be

26RESIDENT PROGRAMMING QUICK REFERENCESome of the programming PPN’s may be commonly used by the resident. Following are quick references to the keystr

27SPECIFICATIONSMECHANICAL Case dimensions: 6.45” W x 10.81” H x 3.74” DELECTRICAL Voltage: 16 Volts AC or 12-24 Volts DC Current: 650 mA AC typ

1PRODUCT DESCRIPTIONLinear’s RE-1 Telephone Entry System is designed for residential or light commercial access control applications. The speakerphone

28PROGRAMMING WORKSHEETSENOZEMITSENOZEMITSENOZEMITSENOZEMITSENOZEMITSYADEVITCASYADEVITCASYADEVITCASYADEVITCASYADEVITCAEMITTRATSEMITTRATSEMITTRATSEMITT

29EDOCYRTNEEDOCYRTNEEDOCYRTNEEDOCYRTNEEDOCYRTNE#YALER#YALER#YALER#YALER#YALERENOZEMITENOZEMITENOZEMITENOZEMITENOZEMITEDOCYRTNEEDOCYRTNEEDOCYRTNEEDOCYR

LINEAR LIMITED WARRANTYThis Linear product is warranted against defects in material and workmanship for twenty-four (24) months. The Warranty Expirati

2INSTALLATION INFORMATIONBefore beginning installation, please review the entire instructions and become familiar with the system’s operation, wiring,

312 RELAY TERMINAL BLOCKFor Relay #1 and Relay #2 output connections to the access control devices.13 RELAY INDICATORSIndicators for Relay #1 and Rela

4WIRING DIAGRAMGATEOPERATOROPEN16 VAC20 VATRANSFORMERTELCOOPEN #1KEYPAD GNDKEYPAD DAT 1KEYPAD DAT 0KEYPAD PWRTRANSFORMERTRANSFORMERBATTERY NEGATIVEBAT

5ENTRY SYSTEM MOUNTINGPedestal MountingThe RE-1 Entry System can be mounted on a standard pedestal.1. Open the RE-1 case by removing the two security

6TELEPHONE WIRING OPTIONSShared LineThis is the standard confi guration. The telephone line is routed through the RE-1 to the house phones. Pressing th

7MULTIPLE UNIT INSTALLATIONSAny of the four basic operation modes (Shared Line, Dedicated Line, Intercom, and Ring Down) may be used with multiple RE-