Linear XR-4 Manuel d'utilisateur télécharger pdf

INSTR,INSTL,XR-4

LINEAR P/N: 215194 C

MATERIAL: 20 LB. MEAD BOND

SIZE: 8.500" X 11.000"

SCALE: 1-1

INK: BLACK

SIDE 1 OF 2 (FRONT)

XR-4

XTENDED RANGE

FOUR CHANNEL

SUPERVISED

STATIONARY

RECEIVER

For Use With Linear’s

XR Series Xtended

Range Transmitters

Installation

Instructions

(760) 438-7000 • FAX (760) 438-7043

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com

1. PRODUCT DESCRIPTION

Linear’s Xtended Range FM receivers and transmitters are designed for use in various

wireless remote control applications. When the Model XR-4 receiver detects a signal from its

companion transmitter, it will verify the digital code, activate the correct output channel, and

trigger the remote device connected to the receiver.

The XR-4 receiver has full supervision capabilities. If the “status” option is selected, the

receiver expects hourly status signals from its transmitter. If these signals cease, the receiver

will indicate trouble by activating its status output after four hours. Contact supervision allows

the receiver’s outputs to follow the transmitter’s inputs, each output staying activated as long

as each transmitter input is activated. Alternately, an “auto-restore” option can be selected in

the transmitter, causing a momentary receiver output each time any transmitter input is

activated. If the transmitter sends a low battery signal, the receiver’s low battery output will

activate.

Power for the XR-4 receiver can come from an external 12 VDC power supply (Linear Model

T-1224DC) or from a 12-volt battery. A diode protects the unit from reverse power polarity.

The XR-4 draws about 30 mA standby, and about 190 mA when all outputs are active. The

receiver outputs provide isolated N/O and N/C relay contacts for each channel capable of

switching a maximum of 1 Amp @ 32 VDC each. The low battery and status outputs are solid

state and are capable of switching up to 50 mA @ 20 VDC to ground.

Two antennas (sold separately) are available for the XR-4. The Model ANT-1A is an 8-inch

“rubber duck” antenna for short range applications (less than 1 mile). The ANT-1A requires

a CON-180A (straight) connector to mate the antenna to the transmitter. For a right angle

antenna, use the CON-180A plus the CON-90A.The Model ANT-2 is a 3-foot whip antenna

for use in long range or difficult installations where more range from the XR-4 is required. A

common 9-foot 1/4 wave CB whip antenna can also be used with the XR-4 for maximum

range.

Two 8-position switches set the unit’s system code. This code must be matched in the XR-4’s

transmitter(s). There are 65,536 different system codes possible. The 4-position option switch

selects the status supervision option for each channel.

The receiver is housed in a rugged weather-resistant metal enclosure with a sturdy SO-239

antenna connector and a water-tight wiring strain relief bushing. Two indicators are visible

through a window on the case. The green power indicator lights when the receiver has power.

During reception, the red RF indicator lights. Two internal test points are provided for signal

strength and audio monitoring.

2. OPEN RECEIVER

3. COMPONENT LOCATIONS 4. INSTALLATION TIPS 5. MOUNT RECEIVER CASE

If using the ANT-1A antenna: For best range mount the XT/XR unit to a metal plate with a

minimum size of 12" x 12". The ANT-1A antenna should extend above the mounting plate

and be free of obstructions. If the ANT-1A antenna cannot be mounted in the open, consider

using an extension coaxial cable with PL-259 connectors to move the antenna’s location.

The XT/XR series of radios operate in the 27 MHz Citizens Band (CB) and may use any CB

antennas or CB antenna accessories. Antennas, PL-259 extension cables and other adapters

are available at Radio Shack® or other electronics stores.

18-FOOT CABLE

UNIVERSAL

MOUNTING BRACKET

3-FOOT

ANT-2

ANTENNA

8-INCH

ANT-1A

ANTENNA

STRAIGHT-THRU

CONNECTOR

(CON-180A)

RIGHT ANGLE

CONNECTOR

(CON-90A)

USE ANT-1A ANTENNA FOR

SHORT RANGE APPLICATIONS

(LESS THAN 1 MILE)

USE ANT-2 ANTENNA FOR MAXIMUM

RANGE OR DIFFICULT APPLICATIONS

LINE-OF-SIGHT

BETWEEN THE

TRANSMITTER AND

RECEIVER ANTENNAS

WILL PROVIDE THE

BEST RANGE

ANTENNAS ARE MOUNTED

VERTICALLY, ON HIGH POINTS

OF BUILDINGS

TRANSMITTING THROUGH

STRUCTURES, METAL AND

GEOGRAPHIC OBSTACLES WILL

REDUCE RADIO RANGE

BAD INSTALLATIONGOOD INSTALLATION

AT LEAST 9 FEET

ABOVE GROUND IS

RECOMMENDED

MOUNT ANTENNA AS HIGH AS POSSIBLE

WHEN MOUNTING ON

THE SIDE OF A

STRUCTURE, USE A

MINIMUM OF A 3-FOOT

SPACER TO DISTANCE

THE ANTENNA FROM

THE STRUCTURE

GOOD ANTENNAS NEED GOOD GROUNDS

IDEALLY, A GROUND

PLANE WITH A RADIUS

OF NINE FEET MINIMUM

IS DESIRED

9 FEET

METAL ROOF

ANTENNA LOCATION IS

OF PRIMARY CONCERN

FAIR

POOR

REMOVE FOUR

CASE SCREWS AND

SLIDE OUT CIRCUIT

BOARD

CASE SCREWS

END CAP STAYS

ATTACHED TO

THE CIRCUIT

BOARD

BOARD FITS IN

3RD SLOT UP

REFERENCE

CARD FITS IN

1ST SLOT

SYSTEM CODE

SWITCHES

ANTENNA

CONNECTOR

(HIDDEN)

STATUS

SWITCH

RF SIGNAL

INDICATOR

(RED)

POWER

INDICATOR

(GREEN)

POWER & OUTPUT

TERMINAL BLOCK

TEST POINTS

AUDIO

OUTPUT

SIGNAL

LEVEL

GROUND

SWITCH "A"

SWITCH "B"

MOUNT UNIT WITH

TWO BOTTOM SCREWS

(DON'T INSTALL TOP

SCREWS UNTIL WIRING

IS COMPLETE)

UNIT SHOULD BE

MOUNTED IN SHELTERED

LOCATION WITH ACCESS

TO ANTENNA CO-AX AND

POWER/SIGNAL WIRES

WARNING: THIS

PRODUCT SHOULD NOT

BE USED IN LIFE

SAFETY APPLICATIONS.

FCC Rules allow

unlicensed high-power

transmissions at or near

the operating frequency

of this product which

may interfere with, or

even disable, normal

operation of this radio

device.

1 2

Résumé du contenu

Page 1 - XTENDED RANGE

INSTR,INSTL,XR-4LINEAR P/N: 215194 CMATERIAL: 20 LB. MEAD BONDSIZE: 8.500" X 11.000"SCALE: 1-1INK: BLACKSIDE 1 OF 2 (FRONT)XR-4XTENDED RANGE

Page 2 - TRANSMITTER IS TRIGGERED

INSTR,INSTL,XR-4LINEAR P/N: 215194 CMATERIAL: 20 LB. MEAD BONDSIZE: 8.500" X 11.000"SCALE: 1-1INK: BLACKSIDE 2 OF 2 (BACK)6. SET RECEIVER SW

Commentaires sur ces manuels

Pas de commentaire

Linear XR-4 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Antennes de réseau Linear XR-4. Linear XR-4 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels