Linear XR-4 Manuel d'utilisateur télécharger pdf (Page 2)

INSTR,INSTL,XR-4

LINEAR P/N: 215194 C

MATERIAL: 20 LB. MEAD BOND

SIZE: 8.500" X 11.000"

SCALE: 1-1

INK: BLACK

SIDE 2 OF 2 (BACK)

6. SET RECEIVER SWITCHES 7. CONNECT POWER AND OUTPUTS 8. MOUNT ANTENNA AND ROUTE CABLE

9. TEST SYSTEM 10. COMPLETE INSTALLATION LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship

for twelve (12) months. The Warranty Expiration Date is labeled on the product.

This warranty extends only to wholesale customers who buy direct from Linear or

through Linear’s normal distribution channels. Linear does not warrant this product

to consumers. Consumers should inquire from their selling dealer as to the nature of

the dealer’s warranty, if any. There are no obligations or liabilities on the part of

Linear LLC for consequential damages arising out of or in connection with use

or performance of this product or other indirect damages with respect to loss of

property, revenue, or profit, or cost of removal, installation, or reinstallation. All

implied warranties, including implied warranties for merchantability and implied

warranties for fitness, are valid only until Warranty Expiration Date as labeled on the

product. This Linear LLC Warranty is in lieu of all other warranties express or

implied.

All products returned for warranty service require a Return Product Authorization

Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#

and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need

in portable wireless signaling. However, there are some limitations which must be

observed.

1 WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow

unlicensed high-power transmissions at or near the operating frequency of this product which may

interfere with, or even disable, normal operation of this radio device.

1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95

Radio Control devices. As such, they have limited transmitter power and therefore limited range.

1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals

that occur on or near their operating frequencies, regardless of code settings.

1 Changes or modifications to the device may void FCC compliance.

1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or

dealer, and these facts should be communicated to the ultimate users.

ANT-1A

ANTENNA

USE ANT-1A ANTENNA

FOR SHORT RANGE (LESS

THAN 1 MILE)

APPLICATIONS

CON-180A

STRAIGHT

CONNECTOR

CON-180A + CON-90A

ANGLE CONNECTOR

MOUNT ANTENNAS AS HIGH AS POSSIBLE

(A METAL MOUNTING POLE IS RECOMMENDED)

AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THE

ANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED.

USE RG-8 FOR UP TO 100-FOOT CABLE RUNS.

TO UNIT

USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGER

RANGE APPLICATIONS OR DIFFICULT

INSTALLATIONS

GND

LOW BATTERY & STATUS

OUTPUTS WILL SWITCH

UP TO 50 mA @ 20 VDC

TO GROUND WHEN ACTIVE

EACH RELAY OUTPUT WILL SWITCH

UP TO 1 AMP @ 32 VDC

+ 12 VDC

LOW BAT

STATUS

N/O

COM

N/C

N/O

COM

N/C

N/O

COM

N/C

N/O

COM

N/C

CH 1 CH 2 CH 3 CH 4

RECEIVER CURRENT:

<30 mA STANDBY

<190 mA WITH ALL RELAYS ENERGIZED

USE 18-24 AWG WIRE

TO CONNECT POWER

AND OUTPUTS

ROUTE WIRES THROUGH CASE

STRAIN RELIEF BUSHING BEFORE

CONNECTING TO TERMINALS

WARNING

THIS UNIT REQUIRES 12 VDC AT 1/2 AMP.

THE NO-LOAD VOLTAGE OF THE SUPPLY

MUST NOT EXCEED 17.5 VDC OR DAMAGE

TO THE UNIT WILL OCCUR!

FROM 12 VOLT, 1/2 AMP

POWER SOURCE

SECURE END PLATE BY

INSTALLING THE FOUR

CASE SCREWS

TIGHTEN WIRING STRAIN

RELIEF BUSHING TO

SECURE AND WEATHER

PROOF WIRING

INSTALL THE TWO REMAINING

MOUNTING SCREWS

TEST SYSTEM AGAIN AFTER

COMPLETING INSTALLATION

SLIDE BOARD INTO

CASE IN THE 3RD

SLOT UP

TRANSMITTER

RECEIVER

INSTALL AND SETUP

THE COMPANION UNIT

AS DESCRIBED IN ITS

INSTALLATION

INSTRUCTIONS

APPLY POWER AND TRIGGER THE

TRANSMITTER'S INPUT

THE TRANSMIT INDICATOR

SHOULD LIGHT WHEN THE

TRANSMITTER IS TRIGGERED

THE RECEIVER'S SIGNAL

INDICATOR SHOULD LIGHT AND

OUTPUT SHOULD ACTIVATE

IF SYSTEM FAILS TEST, CHECK POWER, SWITCH

SETTINGS AND ANTENNA CONNECTIONS

WARNING

NEVER CONNECT THE TRANSMITTER AND

RECEIVER ANTENNA CONNECTORS

DIRECTLY TO EACH OTHER. MAJOR

DAMAGE TO BOTH UNITS WILL OCCUR!

SET SYSTEM CODE SWITCHES A & B

TO MATCH SYSTEM CODE SWITCHES

A & B IN THE TRANSMITTER

OPTION SWITCH

SYSTEM CODE SWITCHES

SWITCH #

CHANNEL #

SWITCH 1 CH 1

OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 1

SET SWITCHES 1 -4 TO SELECT THE CHANNELS THAT WILL

REQUIRE STATUS REPORTS FROM THE TRANSMITTER(S)

SWITCH "A"

SWITCH "B"

ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 1

SELECTION

OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 2

OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 3

OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 4

ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 2

ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 3

ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 4

SWITCH 2

SWITCH 3

SWITCH 4

CH 2

CH 3

CH 4

1 2

Commentaires sur ces manuels

Pas de commentaire

Linear XR-4 Manuel d'utilisateur Page 2

Commentaires sur ces manuels