Linear DVS-2400 Manuel d'utilisateur télécharger pdf (Page 37)

Black 0037

Black0037

COMMUNICATOR REPORTING OPTIONS

REPORTING FORMAT

◆

The factory setting causes the communicator to

report using the 4 by 2 format. This format

allows four-digit account numbers from 0000 to

9999 and provides two-digit alarm codes.

◆

Alternately ADEMCO CONTACT ID can be

chosen as a reporting format. This format allows

4-digit account numbers from 0000 to 9999 and

provides verbose report descriptions with

Ademco Contact ID compatible Central Stations.

CALL ROUTING

◆

The factory setting for the communicator is to

route all calls to the primary telephone number.

If communication is unsuccessful after five

attempts to the primary number, the secondary

number will be dialed for an additional five

attempts. If the secondary number cannot be

reached, the communicator will “sleep” for five

minutes before starting the call process over

again. A total of five sleep cycles (50 call

attempts) can occur before the communicator

stops calling.

◆

Alternately, the communicator can be

programmed to report supervisory events (low

batteries, radio trouble, etc.) to the supervisory

telephone number instead of the primary or

secondary telephone numbers.

✍

CAUTION: If the page alert user code feature is

going to be used, the supervisory number is

reserved for the pager number. DO NOT SET THE

CALL ROUTING OPTION TO “1”.

◆

To disable supervisory reports, set call routing

option to “1” and remove the supervisory

telephone number or in 4 by 2 set the report to 0.

✍

NOTE: Do not program the primary and secondary

telephone numbers the same. See the FCC

Telephone Rules and Regulations on the rear

cover of this manual.

COMMUNICATOR REPORTING OPTIONS

STEP #

PROGRAMMING

FUNCTION

POSSIBLE

VALUES

FACTORY

VALUE

INSTALLATION

VALUE

86 CALL ROUTING

0 = ALL CALLS TO PRIMARY OR SECONDARY NUMBER

1 = ALL ALARM CALLS TO PRIMARY OR SECONDARY NUMBER AND

ALL OTHERS TO SUPERVISORY NUMBER

88 ACCOUNT NUMBER 4 DIGITS EMPTY

89 PRIMARY PHONE NUMBER UP TO 20 DIGITS EMPTY

90 SECONDARY PHONE NUMBER UP TO 20 DIGITS EMPTY

91 SUPERVISORY/ PAGER PHONE NUMBER UP TO 20 DIGITS EMPTY

FOR ALL PHONE NUMBERS

⇒⇒⇒⇒

PRESSING THE (A) KEY INSERTS A 1-SECOND DELAY

THE [FIRE] KEY INSERTS A 5-SECOND DELAY

THE [CHIME] KEY INSERTS A “

”

THE (A) KEY INSERTS A “#” IF IT IS THE LAST DIGIT OF THE PHONE

NUMBER

105 REPORTING FORMAT 0 = 4 BY 2; 1 = ADEMCO 0

108 REPORT CONSOLE TROUBLE 0 = NO; 1 = YES 0

110 REPORT FORCE ARMING 0 = NO; 1 = YES 0

111 OPEN/CLOSE 0 = NO; 1 = YES; 2 = MASTER PAC ONLY 0

113 POINT ID REPORTING FOR 4 BY 2 FORMAT 0 = NO; 1 = YES 1

Communicator Reporting Option Table

JKL

HOME

AWAY

0 FOR 4 BY 2

1 FOR ADEMCO CONTACT ID

PROGRAMMING STEP #105

PROGRAM

STORE PROGRAM

TUV

MNO

HOME

AWAY

PROGRAMMING STEP #86

PROGRAM

STORE PROGRAM

0 FOR ALL TO PRIMARY/SECONDARY

1 FOR ALARMS ONLY TO

PRIMARY/SECONDARY

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 43 44

Commentaires sur ces manuels

Pas de commentaire

Linear DVS-2400 Manuel d'utilisateur Page 37

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Linear DVS-2400